![how to replace a dishwasher door lock how to replace a dishwasher door lock](https://content.instructables.com/ORIG/FCK/COJF/HHI53JCB/FCKCOJFHHI53JCB.jpg)
Lift the door and move it back onto both hinges.Open door slightly to about a 15 degree angle from the tub.If the dishwasher is integrated and no kitchen door is attached, it will not be possible to test the door. It is normal for a dishwasher door without a kitchen door fitted not to remain open, It will be closed again by the springs on the hinges. The control should then work normally.Īlso to know, why won't my dishwasher door stay open?ġ. To unlock the dishwasher control panel, press and hold the NO HEAT DRY button for 4 deliberate seconds and the LOCK ON light should turn off. Secondly, why is my dishwasher locked? It appears that you are indicating that the control is locked on the console of the dishwasher. Close the dishwasher and pull the front panel off of the unit casing.Use a Phillips head screwdriver to remove the eight screws holding the side panels onto the door.Open your Bosch dishwasher door and allow it rest as if you are going to load dishes into the tray.Remove the power plug from your Bosch dishwasher.
#HOW TO REPLACE A DISHWASHER DOOR LOCK HOW TO#
How to Install Bosch Dishwasher Door Panels Thereof, how do you put the front panel on a Bosch dishwasher? If everything went as expected, you have just performed a complete door lock assembly replacement for your front-loading washer. Contact us for more appliance repair guides or to service your home appliances.To open the door, pull the door handle. Then run a load to see if it locks and unlocks the way it’s supposed to. Give yourself a pat on the back. – Test the Doorįinally, plug your washer back in, push it back into place, and begin testing. Return the brackets and screws into place and fasten them, not too tight, to secure the top panel. – Return Bracket Screws Securing the Top Panel
![how to replace a dishwasher door lock how to replace a dishwasher door lock](https://i.ytimg.com/vi/RRbWJYCWIK0/hqdefault.jpg)
It should now be properly aligned to refasten. Push the top panel forward and lock it into place behind the washer control panel lip. – Push Forward to Set Into Place (Reverse Previous Movement) Set your top panel back into place, set backward so that it is in the correct position to slide into the top of the washer control panel. Reassemble and Test – Set the Top Panel Over the Washer You have just replaced your door lock assembly. Return the mounting screws to their places and fasten tightly. – Fasten by Returning the Mounting Screws Slide the new door lock assembly into the slot, make sure it is correctly upright and align it with the screw holes. – Set the New Door Lock Assembly Into Place Take the new door lock assembly and connect the two halves of the wire harness together at the clip. Install the New Door Lock Assembly – Connect the Wire Clip Halves It will trail wires so be careful – Disconnect the Wire Clipĭisconnect the wires via the clip or “wire harness.” This can usually be done by pressing a releasing tab and pulling the two halves apart. Pull out the old lock assembly through the slot. You will see two screws holding it in place above and below. Standing in front of the washer with the door open, you can see the locking assembly where the door latches into the door socket. – Remove the Front Door Lock Mounting Screws Push or pull the washer door open once the latch is released. Now you can open the washer door to replace the lock assembly. If the door is stuck locked, removing the top makes it possible to reach in and push the white plastic latch that holds it closed. Remove the Door Lock Assembly – Manually Unlock the Door Now you can lift the top panel away and set it aside. You should feel it come loose as it slides. To un-seat the washer top panel, pull the panel back toward you (toward the back of the washer). – Pull the Top Panel Toward the Back of the Washer Remove the screws, and the brackets if necessary, and set them aside. These brackets attach the top panel with screws. Locate the two brackets at the top of the back of the washer. Remove the Top Panel – Remove the Top Panel Bracket Screws Be careful of the water line connections. Turn or pull the washer away from the wall so that you have room to stand behind it and work. This is an electrical repair and you need to remain safe from shocks during the process.
![how to replace a dishwasher door lock how to replace a dishwasher door lock](https://i.ytimg.com/vi/ng-lnB_GRoc/maxresdefault.jpg)
Pull the washing machine’s power cable out from the wall socket. Safe Repair Preparation – Unplug the Washer Fortunately, this is a repair that anyone with a screwdriver and the right replacement part can do at home. Is your front-loading washer door latch acting up? Whether your door is refusing to lock or refusing to unlock at the right times, or no longer acknowledging when the door is locked and safe to roll, it may be necessary to replace your washer door latch assembly entirely.